Honeywell AlarmNet IGSMHS Скачать руководство пользователя страница 9

Страница: 9 / 64

Section 1: General Information

1-5

Environmental

Operating temperature: –20º to +55ºC (

evaluated range: 0º to +49ºC)

Storage temperature: –40º to +70ºC
Humidity: 0 to 85% relative humidity, non-condensing

Altitude: to 10,000 ft. operating, to 40,000 ft. storage

Compatibility

For a list of control panels that are compatible with various features of this communication
module, go to:

http://www.security.honeywell.com/hsc/resources/MyWebTech

After logging on, select the applicable communication product, and then select “Compatibility
Chart” under Essential Docs.

For UL installations, compatible control panels are:



Vista-128BP



Vista-250BP

For UL installations, compatible receivers are:



MX8000

(

– can be used for supplemental reporting in ECP mode when

connected to model 7810iR-ENT; must be used for opening/closing ring

back in Zone Trigger mode when connected to control unit’s DACT.)



7810iR-ENT (

– must be the primary alarm receiver.)



Ademco 685 (

– Ademco 685 has not been evaluated by UL.)

The Automation System must be UL1981 listed.

The IGSMHS has been evaluated for connection to police station receivers.

Содержание AlarmNet IGSMHS

































































Результаты поиска

Содержание AlarmNet IGSMHS

Отзывы:

Honeywell AlarmNet IGSMHS, Инструкция по установке и настройке, Страница: 9 / 64

Результаты поиска

Содержание AlarmNet IGSMHS

Отзывы: