manualshive.com logo in svg

Hitachi SH7750 series, Руководство по оборудованию

Серия продуктов Hitachi SH7750 - мощные процессоры для высокопроизводительных вычислений. Ищите бесплатное руководство по аппаратной части на manualshive.com, чтобы получить полезную информацию о вашем устройстве. Скачайте руководство сейчас, чтобы лучше понять возможности этого продукта.

Поделиться
Скачать
background image

Rev. 6.0, 07/02, page 226 of 986

9.2.2

Peripheral Module Pin High Impedance Control

When bit 6 in the standby control register (STBCR) is set to 1, peripheral module related pins go
to the high-impedance state in standby mode.

•

 

Relevant Pins

SCI related pins

MD0/SCK

MD1/TXD2

MD7/TXD

MD8/RTS2

CTS2

DMA related pins

DACK0

DRAK0

DACK1

DRAK1

•

 

Other Information

The setting in this register is invalid when the above pins are used as port output pins.

For details of pin states, see Appendix E, Pin Functions.

9.2.3

Peripheral Module Pin Pull-Up Control

When bit 5 in the standby control register (STBCR) is cleared to 0, peripheral module related pins
are pulled up when in the input or high-impedance state.

•

 

Relevant Pins

SCI related pins

MD0/SCK

MD1/TXD2

MD2/RXD2

MD7/TXD

MD8/RTS2

SCK2/

MRESET

RXD

CTS2

DMA related pins

DREQ0

DACK0

DRAK0

DREQ1

DACK1

DRAK1

TMU related pin

TCLK

•

 

Other Information

The setting in this register is invalid in the hardware standby mode.

For details of pin states, see Appendix E, Pin Functions.

Содержание SH7750 series














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7750 series

ebm-papst M4Q045-DA13-04 Operating Instructions Manual preview
M4Q045-DA13-04
Бренд: ebm-papst Страницы: 9
Flux F 457 Original Attachment preview
F 457
Бренд: Flux Страницы: 16
V2 LEX-RFO Manual preview
LEX-RFO
Бренд: V2 Страницы: 14
NOVAK BALLISTIC Instructions preview
BALLISTIC
Бренд: NOVAK Страницы: 2
Selve SE Plus-com Operating Instruction preview
SE Plus-com
Бренд: Selve Страницы: 132
VDG TM100B25 Installation Manual preview
TM100B25
Бренд: VDG Страницы: 18
Guangxi Liuzhou Wuling Motors LJ465Q-1ANE1 Instruction Book preview
LJ465Q-1ANE1
Бренд: Guangxi Liuzhou Wuling Motors Страницы: 54
Omega Engineering OMEGAFLEX FPU5-MT-110 User Manual preview
OMEGAFLEX FPU5-MT-110
Бренд: Omega Engineering Страницы: 83
Interpump RS500 Operating Instructions Manual preview
RS500
Бренд: Interpump Страницы: 16
Sachs SA 2-440 Repair Instructions preview
SA 2-440
Бренд: Sachs Страницы: 52
Vanguard 540000 Series Operator'S Manual preview
540000 Series
Бренд: Vanguard Страницы: 104
FUTABA HV S9177SV Quick Start Manual preview
HV S9177SV
Бренд: FUTABA Страницы: 3
YS 56SR Operator'S Manual preview
56SR
Бренд: YS Страницы: 2
RIEJU Century 125 Workshop Manual preview
Century 125
Бренд: RIEJU Страницы: 63
Motion CM-40 Manual preview
CM-40
Бренд: Motion Страницы: 92
Motion CM-07 Manual preview
CM-07
Бренд: Motion Страницы: 124
Wood-mizer LX450 Series User Manual preview
LX450 Series
Бренд: Wood-mizer Страницы: 123
ZIEHL-ABEGG ZA top SM160.30B/S Original Operating Instructions preview
ZA top SM160.30B/S
Бренд: ZIEHL-ABEGG Страницы: 72

Бренды по названию

Популярные бренды

Загрузить еще бренды