Hitachi H8/3044 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 867

background image

Figure 5-5 shows the transitions among the above states.

Figure 5-5 Interrupt Masking State Transitions (Example)

Figure 5-6 is a flowchart showing how interrupts are accepted when UE = 0.

•

If an interrupt condition occurs and the corresponding interrupt enable bit is set to 1, an
interrupt request is sent to the interrupt controller.

•

When the interrupt controller receives one or more interrupt requests, it selects the highest-
priority request, following the IPR interrupt priority settings, and holds other requests
pending. If two or more interrupts with the same IPR setting are requested simultaneously, the
interrupt controller follows the priority order shown in table 5-3.

•

The interrupt controller checks the I bit. If the I bit is cleared to 0, the selected interrupt
request is accepted regardless of its IPR setting, and regardless of the UI bit. If the I bit is set
to 1 and the UI bit is cleared to 0, only NMI and interrupts with priority level 1 are accepted;
interrupt requests with priority level 0 are held pending. If the I bit and UI bit are both set to
1, only NMI is accepted; all other interrupt requests are held pending.

•

When an interrupt request is accepted, interrupt exception handling starts after execution of
the current instruction has been completed.

•

In interrupt exception handling, PC and CCR are saved to the stack area. The PC value that is
saved indicates the address of the first instruction that will be executed after the return from
the interrupt service routine.

•

The I and UI bits are set to 1 in CCR, masking all interrupts except NMI.

•

The vector address of the accepted interrupt is generated, and the interrupt service routine
starts executing from the address indicated by the contents of the vector address.

All interrupts are
unmasked

Only NMI, IRQ , and
IRQ are unmasked

Exception handling,
or I 1, UI 1

a.

b.

2

3

All interrupts are
masked except NMI

c.

UI 0

I 0

Exception handling,
or UI 1

I 0

I 1, UI 0

←

←

←

←

←

←

←

←

103

www.DataSheet4U.com

«
...
115
116
117
118
119
...
»

Содержание H8/3044




































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H8/3044

Бренд: M-Audio Страницы: 10

FrameSaver 9120

Бренд: Paradyne Страницы: 2

Бренд: Delta Tau Страницы: 74

Бренд: Belkin Страницы: 72

Бренд: Teac Страницы: 20

cMT-FHDX Series

Бренд: Maple Systems Страницы: 2

Бренд: NETGEAR Страницы: 2

Бренд: Renesas Страницы: 20

PBE-5AC-300-ISO

Бренд: Ubiquiti Страницы: 28

NIC-FC730i-Mb-2-32G

Бренд: H3C Страницы: 37

Digital Encoder Plus

Бренд: IDT Страницы: 98

Бренд: Supermicro Страницы: 131

Secure Site Manager 16

Бренд: Black Box Страницы: 16

iMarc SLV 9820-2M

Бренд: Paradyne Страницы: 24

Бренд: Renesas Страницы: 67

Бренд: Cowlacious Designs Страницы: 8

Бренд: LevelOne Страницы: 4

Broadband 700 MHz

Бренд: Alcatel-Lucent Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды