manualshive.com logo in svg

Hayward OmniPL HLXPROUPG, Руководство по установке, Страница: 22 / 32

Поделиться
Скачать
Hayward OmniPL HLXPROUPG Скачать руководство пользователя страница 22

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

20

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Finished with Configuration 

Now that all equipment has been configured, select the following:

Customizing / Add Components -

 use this selection to go back into Configuration and make changes.

Save and Restart -

 this selection will save your configuration settings and restart the OmniPL. 

Quick Edit Guide

If additional pool or backyard equipment is added after initial configuration, or you’d like to make a change to an existing configuration setting, re-enter the 

Configuration Wizard and select “Edit”.  After selecting “Edit”, you will be brought to the Quick Edit Main Menu screen as shown below.  Quick Edit allows you 

to go directly to the equipment that you’d like to add/remove/configure.  When you have finished editing the configuration, you will return to this screen to save 

your changes.

QUICK EDIT

configuration

Main Menu

Bodies of Water

Backyard

Sensors

Add Interlock

System Options

Spa Side

Pre Programmed Config (VSP, Htr, Lt) 

New Typical Configuration

New Advanced Configuration

QUICK EDIT

configuration

Edit Current Configuration

Navigation

There are a number of additional buttons that appear in Quick Edit that either have functions unique to Quick Edit or do not appear anywhere else in the system.  

These buttons are as follows:

 

Save

 - Touch this button to save the configuration edit.  This button only appears on the Quick Edit Home screen.

 

Cancel

 - Touch this button to cancel any changes made to the configuration and exit Quick Edit.  This button only appears on the Quick Edit Home 

Screen.

 

Home

 - Touch this button to quickly jump back to the Quick Edit Main Menu Screen to save your changes.  This button appears at the end of every 

configuration pathway.

 

Back

 - Touch this button to go back to the previous set of configurable items.

See page 8 for a full list of buttons that appear during configuration.

As you are using Quick Edit, you will notice that at the end of each pathway, a Home button and a back arrow will appear.  If you are finished making changes, 

press the Home button and then press the Save button to save your configuration.  If you would like to make more changes to the same device, press the back 

arrow.  This will take you back to the last screen of configurable items for that device.  If you would like to continue to make changes, but to a different device, 

press the Home button and then follow the pathway to the new device.  The following pages will explain each configuration pathway.

Begin Using Quick Edit

From the Quick Main Menu Screen, select one of the following buttons and follow the directions on the next page to configure your equipment.

• 

Bodies of Water

• 

Backyard

• 

Sensors

• 

Interlocks/Add Interlock

• 

System Options

• 

Spa Side

Содержание OmniPL HLXPROUPG

































Отзывы:

Нет отзывов