Harris RMXDIGITAL, Руководство по эксплуатации и техническому обслуживанию

Страница: 105 / 118

Revision C • 10/07
H A R R I S C O R P O R A T I O N
A-5
Appendix A VMCC
to the buttons, those two signals must first be
added to the various include lists. This is covered
in the next section on Telco settings.
T T
T T
Telc elc
elc elc
elco C o C
o C o C
o Channels hannels
hannels hannels
hannels
A maximum of six channels can be defined as
RMX d Telco channels by setting the fader chan-
nels’ rotary switches to be a unique Telco number
(from 1 to 6). When an RMX d console is Inspected
by VMCC, the fader channels defined as Telco chan-
nels are captured by the program. However, the
VMCC program does not assign nor use the Telco
number, and hence will allow any fader channel
to be manually set as a Telco channel. In no case,
though, should more than six channels be desig-
nated as Telco channels in VMCC.
The third CR and Studio monitor selector but-
ton (TEL MON) does not have a default assign-
ment in VMCC since the default source (Telco
Monitor bus) must be routed. To assign this signal
to the button, Telco Mon (signal 175) must be
added to the Monitor and Studio 1 Include lists.
The signal can then be set as the Switch 3 source
in the CR Monitor/Studio 1 Keys entry boxes.
The TEL REC signal (Telco Record, signal 173)
must also be included on the Meter Include List
so it can be assigned to meter switch 3. It is rec-
ommended that the TEL REC signal also be in-
cluded in the Monitor and Studio 1 Include lists
so that the board operator and talent can easily
monitor the Telco record signals. The non-assigned
signals in the CR Monitor and Studio 1 include
lists are “dialed-up” by the operator using the two
monitor source selectors.
E E
E E Ex
x
x x xtr
tr
tr tr tra L
a L
a L a L a Lo
o
o o ogic Input S
gic Input S
gic Input S gic Input S gic Input Selec
elec
elec elec elections
tions
tions tions tions
VMCC has a list of logic commands that can be
assigned to remote mic control panel buttons. In-
cluded in this list are several signals that are only
available on the BMX digital console. The signals
that should not be selected on RMX
digital include:
Talk to Studio 1 Co-Host, Talk to Studio 2, Talk
to Studio 2 Host and Talk to Studio 2 Co-Host.
Setting a button to these logic command does not
cause problems, but they will not do anything on
an RMX
digital since it does not have any method
to use these specific logic commands.
D D
D D Duplic
uplic
uplic uplic uplica
a
a a attttte C
e C
e C e C e Communit
ommunit
ommunit ommunit ommunity N
y N
y N y N y Names
ames
ames ames ames
VMCC allows multiple files to be saved with the
same name since each one has a unique creation
date. To avoid confusion, especially if there are
multiple VMCC users, assign a unique name for
each new community after it’s first created.
Editing Card Complement on a Device
When editing the card complement on any de-
vice, you must wait for the processing to complete
or else program errors could be introduced. Pro-
cessing is complete once the community text
blinks.
Edge Device Parent Reassignment
Each edge device has an assigned “parent” which
is the community member with that edge device’s
setup information in its
edgedevice.ini
file.
If an existing edge device is assigned to a new
parent in VMCC, the updated
edgedevice.ini
file will have to be provisioned and distributed to
all of the affected consoles and cardframes to ef-
fect the parent change on the edge device.
When there are dozens of edge devices in a com-
munity, the affected edge device may not “hear”
the Initialize RCED command issued by VMCC
after the new parent file is distributed. To ensure
the edge device is using the correct file, power cycle
that edge device to force it to retrieve its setup
information from its new parent.
N N N N Nesting E esting E esting E esting E esting Edge D dge D dge D dge D dge De e e e evic vic vic vic vices es es es es
When Nest edge devices is checked under
Tools\Options\General tab, adding a new edge