Harris RMXDIGITAL, Руководство по эксплуатации и техническому обслуживанию

Страница: 80 / 118

Revision C • 10/07
H A R R I S C O R P O R A T I O N
4-22
4 RMX digital Server
while channel 2 is immediately turned Off—even
if the channel is on-air.
Typically, there are no entries under the
[On]
heading unless the console is being setup for non-
attended operation (e.g. slaved to a digital deliv-
ery system).
[TelcoRecord] and [TelcoMonitor]
Each Telco channel can be assigned to the Telco
Monitor bus and/or to the Telco Record bus un-
der these two sections. To assign the Telco chan-
nel, the default setting (
=0
) is changed to
=1
. This
sets that Telco channel as active on that bus as in:
[TelcoRecord]
Channel_81=1
Channel_82=0
Channel_83=0
Channel_84=0
This sets Telco channel 1 (ID # 81) as feeding
the Telco Record output, while the other Telco
channels do not feed the Telco Record output.
SESSION FILE SECTION SUMMARY
Within each of these sections, each channel but-
ton can be set either On (
=1
) or Off (
=0
) when the
session file loads:
•
[Cue]
Sets whether cue is on or off for
each channel.
•
[Send_1]
Sets whether the channel is as-
signed to the send bus.
•
[Prog_1, Prog_2, Prog_3, Prog_4]
Sets whether the channel is assigned to any
of the Program buses.
•
[Offline_1]
Sets whether the channel
is assigned to the Offline bus.
•
[Send_1_PF]
Sets whether the channel’s
send feed is pre-fader or post-fader (default).
•
[Send_1_PS]
Sets whether the channel’s
send is pre-switch or post-switch (default).
•
[PanBalance]
Sets whether the channel’s
pan/balance control is on or off.
•
[TelcoAuto]
Sets whether the Auto
Foldback feature is on or off for each Telco
channel.
•
[TelcoRecord]
Sets whether the Telco
channel feeds the Telco Record bus.
•
[TelcoMonitor]
Sets whether the Telco
channel feeds the Telco Monitor bus.
•
[Mode]
Sets the channel’s default mode.
This section has four values: Stereo (
=0
),
Left only (
=1
), Right only (
=2
), or Mono
Sum (
=3
).
•
[local_cough] S
ets whether the On but-
ton functions as a cough button when the
channel source is a mic and it is On. Press-
ing and holding the On button removes the
mic’s audio from all assigned buses.
•
[timer_reset]
Sets the channel to re-
set the event timer, when the timer’s Auto
button is lit, when the channel is turned
On. If Auto is not lit, or if the entry is
=0
,
then there is no timer reset at channel on.
•
[fader_start]
Sets the channel to au-
tomatically turn on when the fader is moved
up from full off and to turn off when moved
back to full off.
=0
means fader movement
does not affect on/off status.
•
[port_event_card_x]
Commands a
logic output for any Assignable logic con-
nector on the KSU (
card_4
) and the three
possible 8-Input Expansion cards (
card_1
,
card_2
,
card_3
).
There could be up to sixteen line entries
under the heading:
port_event_j=k
to
define each port.
j
is the port number (from
1 to 16) with the event function
k
(0 is a
null event and 1 is a trigger).
CHANNEL LOCKOUT SECTION
This section sets whether any channel buttons
are locked out, preventing changes to the session
file settings by the board operator. Channel lock-