H3C S12500-X Скачать руководство пользователя страница 83

Страница: 83 / 168

Figure 54

Replacing a switching fabric module (2)

Replacing a fan tray

WARNING!

•

When replacing a fan tray while the switch is running, be aware of electrical safety hazards.

•

To avoid bodily injury, do not touch the rotating fans when you replace the fan tray.

•

To avoid device damage and bodily injury, use two people to replace a fan tray.

When the fan tray fails, replace the fan tray to ensure normal operation of the switch.
For an S12510-X AC/S12510-X DC switch, if only one fan tray is used, install it in the slot FAN2 to ensure

good ventilation.
For an S12516-X AC/S12516-X DC switch, make sure both fan trays are installed on the switch and can

operate correctly.
The S12500-X switches provide the following types of fan tray slots:

•

Horizontal slots in the S12510-X AC/S12510-X DC switch

•

Vertical slots in the S12516-X AC/S12516-X DC switch

The procedures for replacing fan trays in both types of slots are the same. This section describes how to

replace a horizontally-orientated fan tray in an S12510-X AC.

Содержание S12500-X









































































































































































Результаты поиска

Содержание S12500-X

Отзывы:

Похожие инструкции для S12500-X

Бренды по названию

Популярные бренды

H3C S12500-X, Руководство по установке

Результаты поиска

Содержание S12500-X

Отзывы:

Похожие инструкции для S12500-X

Бренды по названию

Популярные бренды