H3C S12500-X Скачать руководство пользователя страница 129

Страница: 129 / 168

120

Figure 65

Power module LEDs

(1) Power input LED

(2) Power output LED

(3) Over-temperature alarm LED

(4) Fault LED

Table 67

Power module LED description

Power input

LED (green)

Power output

LED (green)

Over-temperature

alarm LED (yellow)

Fault LED

(red)

Description

Steady on

Off

The power module is operating
correctly.

Steady on

Off

An over-temperature alarm has
occurred.

Steady on

Off

Steady on

The power module is powered off
because of over-temperature.

Flashing Off

Off

The power input has exceeded or
dropped below the threshold.

Steady on

Off

Steady on

The power module is powered off
because of overvoltage.

Steady on

Flashing

Off

The power output is overloaded.

Off

No power is being input.

Steady on

Steady on/Off Off

Steady on

Unidentified power module
faults.

Содержание S12500-X









































































































































































Результаты поиска

Содержание S12500-X

Отзывы:

Похожие инструкции для S12500-X

Бренды по названию

Популярные бренды

H3C S12500-X, Руководство по установке

Результаты поиска

Содержание S12500-X

Отзывы:

Похожие инструкции для S12500-X

Бренды по названию

Популярные бренды