H3C S12500-X Скачать руководство пользователя страница 124

Страница: 124 / 168

115

Figure 64

LSX1SUP10A1 LEDs

(1) Management Ethernet port LED (LINK)

(2) Management Ethernet port LED (ACT)

(3) Fan LED

(4) Power module status LED

(5) Card status LEDs

(6) MPU active/standby status LED

Management Ethernet port LEDs

The MPU has one LINK LED and one ACT LED to indicate the link status and data forwarding status of the

management Ethernet port.

Table 53

Management Ethernet port LED description

LINK ACT

Description

On Flashing

A link is present, and the management Ethernet port is receiving or
sending data.

Off

A link is present.

Off

No link is present.

Fan LEDs

The MPU provides two LEDs (OK and FAIL) to indicate the status of the fan tray.

Table 54

Fan LED description

OK FAIL Description

Off

All fan trays are operating correctly.

Off

A fan tray problem is present or no fan tray is in position.

Off

The switch is not powered on.

Power module status LEDs

The MPU provides two LEDs (OK and FAIL) to indicate the status of the power modules.

Table 55

Power module LED description

OK FAIL Description

Off

All power modules are operating correctly.

Off

A minimum of one power module is faulty.

Off

The switch is not powered on.

Содержание S12500-X









































































































































































Результаты поиска

Содержание S12500-X

Отзывы:

Похожие инструкции для S12500-X

Бренды по названию

Популярные бренды

H3C S12500-X, Руководство по установке

Результаты поиска

Содержание S12500-X

Отзывы:

Похожие инструкции для S12500-X

Бренды по названию

Популярные бренды