manualshive.com logo in svg

Global Contract Bridges II, Руководство по установке

Поделиться
Скачать
Global Contract Bridges II Скачать руководство пользователя страница 52

Page

•

  

globalcontract.com

51

• Summer 2017

GLOBAL

Contract

INSTALLATION GUIDELINES

Connecting Seat to Bridges Tables Continued

STEP 6: Install six fl at brackets as illustrated.

STEP 7: Rest the 30” deep work surface on the fl at backrest.

STEP 8: Rest the 6” deep work surface with the Rear vertical board on the fl at 
brackets. Align both table assemblies and both work surfaces. Ensure that all 
work surfaces are aligned, without gaps drive supplied wood screws through pre-
installed fl at brackets to secure both work surfaces.

STEP 9: Prepare Seat side boards for installation. Use short Euro screws to 
secure three brackets near top of both Side boards.

STEP 10: Bring the Side boards beside table legs as illustrated. Make sure that the 
rear of the Side board (identifi ed by through holes) is positioned at the back. Slide 
the Side board brackets into the gap between work surfaces and the leg beams.

STEP 11: Align Side board and Rear board holes. Use Allen key to secure both 
Side boards to the Rear board with 4 supplied screws.

STEP 12: Secure both Side panel bracket to the work surfaces with supplied 
wood screws. installing two Back 2 Back seats.

STEP 13 Slide seat in place. Ensure that the front legs of the seat are aligned 
with table legs.

STEP 14 and secure the rear work surface with supplied screws.

Repeat STEPS 2 - 11 when installing two Back 2 Back seats.

7

8

6

9

11

13

12

10

10

12

NOT UL LISTED

Содержание Bridges II

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды