manualshive.com logo in svg

Global Contract Bridges II, Руководство по установке

Поделиться
Скачать
Global Contract Bridges II Скачать руководство пользователя страница 38

Page

•

  

globalcontract.com

37

• Summer 2017

GLOBAL

Contract

INSTALLATION GUIDELINES

Accessory Rail Installation Single Sided

Table mounted accessory rail kits vary in length and in types of supporting verti-
cal uprights:

Identify the required rail length and specifi ed support type.

DOUBLE SIDED RAIL FOR BACK-2-BACK TABLE APPLICATIONS:

STEP 1: Slide both upright brackets into corresponding grooves in the back of 
both rail assemblies.

STEP 2: Adjust position of both rails. 

STEP 3: Raise the entire assembly through the gap between the work surfaces. 

STEP 4: Align the bottom brackets with pilot holes in the bottom of each work 
surface and secure with supplied wood screws. 

STEP 5: Ensure that both rails are centred or adjust as needed. Loosen screws se-
curing the uprights to the work surfaces should you encounter diffi culties sliding 
the rails sideways and retighten. 

STEP 6: Ensure that all transparent injection moulded caps are in place.

5

3

4

2

1

6

Содержание Bridges II

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды