manualshive.com logo in svg

Global Contract Bridges II, Руководство по установке

Поделиться
Скачать
Global Contract Bridges II Скачать руководство пользователя страница 24

Page

•

  

globalcontract.com

23

• Summer 2017

GLOBAL

Contract

4

INSTALLATION GUIDELINES

Note: Side 2 Side laminate divider can be installed in the middle of a work surface and 
over two adjacent work surfaces supported by round legs. Because rectangular legs 
occupy bottom corners of work surfaces it cannot be installed over two adjacent work 
surfaces unless they are supported by 34” deep Back 2 Back leg.

Installation guidelines are the same for both fl ush & extended Side 2 side Dividers. The 
bend direction on the front bracket and hole location on laminate are the only differ-
ences.

STEP 1: Align the front bracket with pilot holes at the bottom of Side 2 Side laminate 
divider and secure with supplied screws.

STEP 2: Align the rear bracket with pilot holes at the rear edge of Side 2 Side laminate 
divider and secure with supplied screws.

STEP 3: Slide the divider over the front edge of a work surface at the desired location.

STEP 4: Attach connector 2 brackets with supplied acorn cap nut. once tight, adjust 
divider’s position and secure it to work surface with supplied screws as illustrated.

1

4

Side 2 Side Laminate Divider

2

3

NOT UL LISTED

Содержание Bridges II

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды