manualshive.com logo in svg

Global Contract Bridges II, Руководство по установке

Поделиться
Скачать
Global Contract Bridges II Скачать руководство пользователя страница 27

•Page

 

globalcontract.com

26

• Summer 2017

GLOBAL

Contract

INSTALLATION GUIDELINES

Half Height Rectangular Leg Gable

Note: Rectangular leg gables can only be installed on rectangular legs. Proceed by 
removing vertical cable manager from both legs fi rst.

STEP 1: Align top brackets with pilot holes and secure with supplied screws.

STEP 2: Align bottom brackets with pilot holes as illustrated and secure with supplied 
screws.

STEP 3: Slide the bottom brackets under the bottom of the leg extrusion.

STEP 4: Wiggle the gable slightly up while making sure that both bottom brackets are 
engaged with the leg extrusion.

STEP 5: Rotate into vertical a position until both top brackets come between the bottom 
of the worksurface and the horizontal leg beam.

STEP 6: Secure the top brackets with two supplied screws while making sure that the 
bottom tabs remain engaged in the leg groove.

1

2

6

5

6

4

3

NOT UL LISTED

Содержание Bridges II

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды