manualshive.com logo in svg

Global Contract Bridges II, Руководство по установке

Поделиться
Скачать
Global Contract Bridges II Скачать руководство пользователя страница 47

•Page

 

globalcontract.com

46

• Summer 2017

GLOBAL

Contract

INSTALLATION GUIDELINES

NOT UL LISTED

Seat partition kit consists of two side gables and one rear partition.

STEP 1: Insert provided pins into gable fi ttings on both side partitions as il-
lustrated.

STEP 2: Align gables with the back panel; align pins with fi ttings in the back 
panel. Tap the gables gently and ensure that all pins are fully engaged.

Note: Before tapping, cover the fabric on the external surface of the side parti-
tion to prevent the fabric from getting soiled.

Seat Partitions

Seat Privacy Partitions

Seat privacy partition kit consists of two side gables and one rear partition.

Each non-handed back divider features four side fi ttings with hooks pointing 
downward as well as two sets of fi ttings mutually securing the back dividers 
together. Handed gables feature fi ttings with slots as well as two sets of fi ttings 
mutually securing the gables vertically together. Floor-level gables feature holes 
for seat brackets pointing in, toward the seat.

STEP 1: Insert provided pins into gable fi ttings on both side partitions as il-
lustrated.

STEP 2 Align gables with the back panel; align pins with fi ttings in the back 
panel. Tap the gables gently and ensure that all pins are fully engaged.

Before tapping, cover the fabric on the external surface of the side partition to 
prevent the fabric from getting soiled.

1

2

1

2

Содержание Bridges II

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды