manualshive.com logo in svg

Global Contract Bridges II, Руководство по установке

Поделиться
Скачать
Global Contract Bridges II Скачать руководство пользователя страница 14

Page

•

  

globalcontract.com

13

• Summer 2017

GLOBAL

Contract

INSTALLATION GUIDELINES

5

6

Base Feed

Identify type and location of required electric components and position
them in accordance with layout plans.

NOTE: four oblong holes in the Power feed mounting bracket must always 
align with four oblong holes in the Power Trough, regardless the Power Trough 
mounting bracket position.
Position of the Power Trough mounting brackets (inner or outer set of oblong 
holes), is governed by the table leg position: 
• outer pair of oblong holes for extended position when the table leg is shared 
  between two adjacent tables, and
• inner pair of oblong holes when the table leg is tucked under the table, at the
  end of a table run.

STEP 1: Secure Power Feed to the Power Trough brackets (ensure that the 
liquid tight whip is long enough to reach the power source / fl oor monument).

STEP 2: Lift the Power Trough on one side and rest the Power Feed mounting 
bracket on top of the Power Trough brackets.

STEP 3: Lower the Power Trough so that the Power Feed bracket is sandwiched 
between the Power Trough and Power Trough supporting brackets; ensure that 
threaded studs protrude trough the holes in the Power Trough.

STEP 4:  Secure all Power Troughs with supplied nylon thumb nuts.

STEP 5: Connect Power Distribution Housings and Jumper Harnesses on
the ground, just below their future location.

NOTE : There is an arrow and a letter “N” on each Power Distribution Housing 
and on every Jumper Harness referring to the correct position in relation to 
each other.

STEP 6: Install Duplex Receptacles as illustrated, with circuit numbers in ac-
cordance with the electrical plans.

Note the alignment of the Power feed mounting bracket and Power Trough 
oblong holes. Studs on Power Trough brackets point to the inner pair of oblong 
holes - indicating tucked in leg application.

Note the alignment of the Power feed mounting bracket and Power Trough 
oblong holes. Studs on Power Trough brackets point to the outer pair of oblong 
holes - indicating extended, shared leg application.

4

4

3

3

2

2

1

1

Содержание Bridges II

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды