GILES GBF-35, Руководство по эксплуатации и обслуживанию

Страница: 52 / 104

46
Fryer Operation
GBF − 35 / GBF − 50 Fryers
4.01.11.1 Clearing Controller Errors
&
Alarms
4.02 Cooking Procedures
The following sections explain “Best Practice” procedures for cooking with the GBF Series Fryer . Certain optional
features are explained where applicable ... your particular equipment may or may not have these options installed.
This is a multi ­ purpose electric fryer for efficiently cooking a variety of menu favorites, from french fries to seafood.
All food products have specific procedures for preparation & cooking, and every food service business has their own
specific standard operating procedures. When preparing, cooking and serving your menu items, please be sure to
follow all of your own
standard practices & guidelines, as they may supercede some of the processes presented in
this manual ..
NOTE: If an error condition persist and cannot be resolved, it could be an indication of component failure or
system malfunction. Please contact a factory ‐ authorized service agent, or call 800.554.4537 for Giles Technical
Support.
NOTE: When an error/alarm is issued and stops a cooking cycle before it is complete, it may become necessary
to discard any food product that was cooking at the time ... always comply with all local Standard Operating
Procedures & Best Practices.
• OPEN: DRAIN OPEN ­ If vat drain valve is opened (even slightly) while fryer power is ON , alarm sounds, lower
display screen reads OPEn , upper display screen reads “ERROR ALARM ‐ DRAIN IS OPEN”. Power to heating
elements is shutdown and remains OFF until the error is corrected.
Press [ALARM] key ... clear alarm by fully closing the drain valve. After closing valve, the alarm sounds again and
upper display screen reads “CHECK OIL LEVEL, ENSURE VAT IS FULL, IF FULL THEN PRESS [START]” . This is a post ­
alarm notification, alerting the operator to confirm that cooking oil is still at the [FULL] level. Add oil if needed,
then press the [START] key to return to PREHEAT mode ... Fryer will not heat until key is pressed.
• ER03: LOW OIL LEVEL ­ Alarm sounds, lower display shows Er03 , upper display reads “ERROR ALARM ‐ CHECK
OIL LEVEL ‐ ENSURE VAT IS FULL” . Heating elements are shutdown until the condition is corrected. The detected
differential between a temperature probe at the [ADD] level and one attached to a heating element exceeds an
acceptable amount, indicating low oil level, which greatly increases the potential for a vat fire! Press the
[ALARM] key ... allow fryer to cool adequately in order to reset fryer error condition. Add oil to raise level to the
[FULL] mark, as needed.
• ER06: LOW OIL LEVEL Post ­ error Warning ­ After Er03 has been cleared, another alarm sounds. The lower
display shows Er06 , upper display reads “CHECK OIL LEVEL ‐ ENSURE VAT IS FULL ‐ PRESS [START]” . This alarm
alerts operator to confirm that cooking oil is at the [FULL] level. If situation has been corrected, press [START]
key to enter PREHEAT and proceed to continue cooking operations ... Fryer will not heat until key is pressed.
• ER19: MAX. ELEMENT TEMP ­ Temperature of heating element has exceeded the maximum allowed by the
controller. Alarm sounds, lower screen shows Er19 , upper screen reads “ERROR ALARM ‐ MAX ELEMENT
TEMPERATURE”. Power to heating elements is shutdown. Press [ALARM] key ... elements must cool below the
allowable temperature threshold to clear this error. Typical cause is that the heating element has been exposed
due to low oil level (or no oil). False alarms can occur when preheating
cold oil at beginning of the day ... regular
stirring of oil while preheating will help avoid such false alarms.
• ER07: MAX ELEMENT TEMP Post ­ Error Warning ­ After an Er19 error has been cleared, a secondary notification
alarm occurs. The lower screen reads Er07 , upper display reads “MAX ELEMENT TEMP ‐ PRESS [START]” . The
alarm notifies operator that a maximum element temperature error has occurred and is now cleared. Press
[START] key to enter PREHEAT mode ... Fryer will not heat until key is pressed.
During the following steps, instructions indicating to press the [ALARM] key are only to silence the audible alarm
tone ... pressing the key DOES NOT clear the error. Tone automatically silences after about 10 secs.