gefran SBI-DN Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 70

gefran SBI-DN Скачать руководство пользователя страница 61

SBI-DN

61

——————

Interface Board DeviceNet

——————

7.6.2 Edit for the Password setting

The flowchart illustrating Password Setup Editing is shown below. Note that pressing

Cancel at any time returns to the previous Menu or cancels the operation in course.

Refer to chapter 7.8 for Editing.
This menu is used to set the Password. Please note the following:
1)  The default value is 0 (zero) and is equivalent to disabling the Password.
2)  Entering a non-zero value via this Menu automatically enables the Password.
3)  Enter 0 (zero) to disable the Password.
4)  If the Password is enabled, it also becomes active when the “OPTION1” menu is

accessed. As soon as it is attempted to access a Password protected Menu or

menu item, the Password will be requested. If the Password is correctly entered,

it will be deactivated from that moment on, i.e. it is possible to access other

protected Menus and/or menu items without having to specify the password

again.

5) The Password is automatically reactivated when the SBI card Main Menu is

exited.

The following message is displayed to confirm the Password:

Password: XXXXX

Conf. (+yes / -no)

TSB8110

Pressing the “+” key confirms the Password and the system returns to the imme-

diately superior Menu level; from this moment on, the Password is enabled if a

non-zero value was entered or disabled if zero was specified.
Pressing the “-” key returns to Password Edit mode.

Enter Password pressed

Password enabled

or active ?

Enter password

Password OK ?

Enter new Password

Confirm Password?

Exit

Warning

Exit

yes

Save in E2PROM

no

no

yes

yes

no

«
...
59
60
61
62
63
...
»

Содержание SBI-DN







































































Отзывы:

Нет отзывов