Geely CK MR479Q 2007 Скачать руководство пользователя

Страница: 175 / 392

168

7. INSPECT CHARGING CIRCUIT WITHOUT LOAD

(a) I f a b a t t e r y / s t a r t e r t e s t e r i s

available, connect the tester to the

charging circuit as per instructions.

(b) If a tester is not available, connect

an ammeter and voltmeter to the

charging circuit as follows.

Disconnect to the wire from

terminal B of the alternator and

connect it to the negative (-) pole

of the ammeter.

Connect the positive (+) pole of the

ammeter to terminal B of the

alternator.

Connect the positive (+) pole of the voltmeter to terminal B of the alternator.

Ground the negative (-) pole of the voltmeter.

With the engine running from idle to 2,000 rpm, check the reading on the ammeter.

Standard amperage: 10A or less

Standard voltage: 13.2V---14.8V

8. INSPECT CHARGING CIRCUIT WITH LOAD

(a) With the engine running at 2,000 rpm, turn on the high beam headlights and place the blower switch at "4".

Check the reading on the ammeter.

Standard amperage: 20A or more

(b) HINT:

If the ammeter reading is less than standard amperage, repair the alternator.

If the battery is fully charged, the indication value will sometimes be less than standard amperage.

Ammeter

Disconnect Wire
from Terminal B

Battery

Voltmeter

Alternator

Содержание CK MR479Q 2007









































































































































































































































































































































































































Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды

Geely CK MR479Q 2007, Руководство по ремонту

Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды