Geely CK MR479Q 2007 Скачать руководство пользователя

Страница: 272 / 392

265

III. KEY POINTS FOR INSTALLATION

1. Pre-Check

(1) The new airbag or clock spring shall be checked before being installed.

(2) Connect negative (-) terminal cable of the battery.

(3) Connect Hi-DS T to the diagnostic interface (16 connector).

(4) Turn the ignition switch ON.

(5) Read the diagnostic circuit and see if the other locations than the troubled area of the airbag are normal.

(6) Turn the ignition switch ON.

(7) Remove the negative (-) terminal cable from the battery, and protect it with insulating tape for insulation.

2. Installation of clock spring: align the clock spring and install it to the

steering wheel.

Center alignment of the clock spring

Screw up the clock spring clockwise to the end, rotate it counterclock-

wise by 2.5 turns, and align it with the mark (see the figure below).

3. Install the components of the steering wheel and airbag assembly

(1) When the center of the clock spring is aligned, install the components of the steering wheel and airbag

assembly.

(2) After being installed, rotate the left and right sides of the steering wheel to position, and make sure there

is no abnormality.

NOTICE

In case of scrapping an airbag, it shall be noted that the airbag shall be deployed according to the specified

procedures before being scrapped.

When connecting or disconnecting the Hi-DS T, turn the ignition switch OFF first.

NOTICE:

Work must be started 60s after the negative (-) terminal cable is disconnected from battery.

NOTICE:

If the center of the clock spring cannot be aligned, the steering wheel

will not turn midway, or cause bad performance to the clock spring

circuit, consequently hamper the normal action of the airbag.

NOTICE

When installing the components of the steering wheel and airbag assembly, attention should be given to

protect the wire harness of the clock spring from seizure.

Содержание CK MR479Q 2007









































































































































































































































































































































































































Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды

Geely CK MR479Q 2007, Руководство по ремонту

Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды