Geely CK MR479Q 2007 Скачать руководство пользователя

Страница: 290 / 392

283

II. Non-DTC Problem Inspection Table

1 With ignition switch ON (Engine Off),

the ABS warning light does not go on

Likely Causes

[Description]

ABS Warning Light does not go

on, the likely cause may be the open in the

warning light power supply circuit, burned bulb

or damaged warning light drive module.

Burned fuse

ABS Warning Light Bulb burned

Power supply circuit open

ABS Warning Light Drive Module damaged

Check the ABS warning light

fuse in the fuse block

Remove the ECU connector,

does the warning light goes on

with the ignition switch ON?

Check whether the ABS

warning light is burned

Check whether the warn-

ing light power supply cir-

cuit and ground circuit in the

wire harness is open

Check the connector of the

warning light power supply

circuit and ground circuit in

the wire harness

Does the fault reoccur?

Abn.

Replace

Repair the wire harness

Yes

Abn.

Yes

Replace

Repair the wire

harness

Repair the connector

Check whether the wire in the

ABS wire harness connecting

the ABS warning light drive

module and the ECU is short

to ground

Yes

Replace the warning light

drive module

Yes

Refer to "Occa-

sional Problem

Service Key Points"

Содержание CK MR479Q 2007









































































































































































































































































































































































































Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды

Geely CK MR479Q 2007, Руководство по ремонту

Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды