Geely CK MR479Q 2007 Скачать руководство пользователя

Страница: 304 / 392

297

Part IV Air Conditioner and Inside &

Outside Trim

Chapter 1 A/C System

A/C system consists of refrigerating and heating system. The Refrigeration system mainly comprises

compressor, condenser and evaporator. The refrigerant circulation absorbs the heat in the air and discharge

the vapour to lower the temperature in and dehumidify the compartment. The heating system is mainly

composed of heat exchanger and heater. It heats the compartment throught the heat exchanger by heating

the air with the heat from the cooling water in the engine. The control of air temperature, humidity and

velocity of flow in the compartment is realized by independent or joint working of heating and Refrigeration

system.

Section 1 The Structure & Working Principle of Refrigeration System

The structure of Refrigeration system is shown in Figure 1.

Figure 1 The Structure and Working Principle of Refrigeration System

1. Compressor 2. Condenser 3.Receiver/Drier

4.Pressure Relief Valve 5.Expansion Valve 6.Evaporator 7.Blower

Refrigeration system uses vapor compressing refrigeration cycle, comprising the compressor, condenser,

pressure relief valve, evaporator, blower , expansion valve, receiver/drier and pipe.

It's working principle is as shown in the Figure 1. The compressor (1) sucks in the refrigerant gas in the

Содержание CK MR479Q 2007









































































































































































































































































































































































































Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды

Geely CK MR479Q 2007, Руководство по ремонту

Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды