Geely CK MR479Q 2007 Скачать руководство пользователя

Страница: 20 / 392

Section 2 Engine Components Replacement

1. Avoid gasoline ejection when work.

2. Drain the coolant to empty.

3. Remove air filter assembly with hose. See (Figure 23)

4. Remove battery

5. Remove fuel delivery pipe sub-assembly

6. Disconnect water hoses, disconnect heater outlet hose

from A/C hose.

7. Loose nut, remove accelerator control cable

8. Remove throttle body assembly

9. Remove power steering pump reservoir assembly

10. Remove front exhaust pipe assembly

11. Remove steering gear boot

12. Seperate steering column assembly. See (Figure 24)

13. Remove front wheel hub nut

14. Disconnect front wheel vehicle speed sensor (with ABS)

15. Detach steering tie rod ball stud pin assembly

16. Detach front lower swing arm sub-assembly

17. Detach front propeller assembly. See (Figure 25)

Detach front propeller from the shaft hub with plastic hammer.

18. Disconnect transmission shift cable or gear shift level assembly

19. Disconnect clutch cylinder assembly or disconnect clutch cable

20. Detach engine assembly and transaxle

(a) Hoisting engine ;

(b) Remove 3 bolts. Detach the right engine mounting bracket. See (Figure 26) ;

(d) Remove 1 bolt. Detach the rear engine mounting bracket;

(e) Remove engine and transaxle and put them on the pallet;

(f) Jack up the boday.

Figure 23

Figure 24

Figure 25

Figure 26

Содержание CK MR479Q 2007









































































































































































































































































































































































































Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды

Geely CK MR479Q 2007, Руководство по ремонту

Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды