Geely CK MR479Q 2007 Скачать руководство пользователя

Страница: 251 / 392

244

II. TEST INSTRUMENTS

III. TROUBLESHOOTING

1. Basic process of trouble diagnosis

DTC of the present fault may coexist with that of the history fault.

NOTICE:

After the new SRS ECU is installed, the warning light of the SRS, with the ignition switch ON, will be on

for 6s and then go out permanently, indicating SRS works normal. In this case, no service is needed.

Otherwise, system diagnosis and service shall be carried out.

If with the ignition switch ON, the warning light of the SRS is not on, the relevant circuits of the warning

light shall be serviced. Then go on with the operation and enable it to work.

2. Check SRS warning light

(1) Turn the ignition switch ON and find out whether the warning light is on.

(2) Six seconds after the process of ON-OFF, confirm that the warning light goes out permanently.

(3) Otherwise, diagnosis and checking have to be involved in.

3. System Diagnosis

The SRS ECU (HAE2.5) will perform a series of circular diagnostic tests to check the readiness of the SRS

functions. This test can avoid unexpected explosion of the restrain system and in the same time ensure the

necessary explosion in a crash. If a trouble is detected, the SRS ECU (HAE2.5) will store a proper DTC and

turn on the warning light indicating a trouble for service.

Instrument Designation Usage

Check system troubles of the SRS, and

clear the DTC of ECU

Diagnostic detector

(Hi-DS T Scan meter)

Special diagnostic meter

WL Remains

Use scan meter and K line to

connect with Scan Meter ECU

Locate a

Trouble

Trouble-

shooting

C l e a r

DTC

Содержание CK MR479Q 2007









































































































































































































































































































































































































Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды

Geely CK MR479Q 2007, Руководство по ремонту

Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды