Geely CK MR479Q 2007 Скачать руководство пользователя

Страница: 133 / 392

126

Chapter 7 Wheel

Section 1 Tire Inspection

Inspection

1. Check the tires for appearance and proper inflation pressure.

Check for inflation pressure after the vehicle stops for over 15min.

2. Using a dial gauge, check the runout of tire.

The tire runout should be no more than 3.0mm

Notice

(1) You must use specified tire and special wheel rim provided by the authorized service

center, otherwise it may affect the normal safe running of the vehicle and even result in

accidents!

(2) If the wheel rim is damaged, you must go to the authorized service center for service and

replacement! Never use the wheel rim of any other model!

3. Changing tire position

It is recommended to change the tire for each 10000km driving. See the figure for where to change each

tire

4. Inspect wheel dynamic balance

The imbalance should be no more than 8.0g. Otherwise, there will be extra vibration and noise when

driving.

Tire module

Tire inflation

ressure

（

Kpa

）

175/65 R14 82H

220

Front

Содержание CK MR479Q 2007









































































































































































































































































































































































































Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды

Geely CK MR479Q 2007, Руководство по ремонту

Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды