Geely CK MR479Q 2007 Скачать руководство пользователя

Страница: 27 / 392

Check the belt distorn as shown in the figure.

Belt deflection:

20N: 5~6mm

Re-adjust the idler if the deflection does not comply with the regulation.

25. Install timing belt guide wheel. See (Figure 46)

Install guide, place the cup side outward.

26. Install timing belt cover sub-assembly

Torque: 9.3N. m

27. Install crankshaft gear or pulley cover sub-assembly

Torque: 9.3N. m

28. Install timing belt cover

Torque: 9.3N. m

29. Install crankshaft pulley. See (Figure 47)

(a) Align pulley lock key and pulley key groove. Install pulley.

(b) Install pulley bolt Torque: 127N. M

30. Install generator assembly

31. Install water pump pulley

32. Install power steering pump V-belt

33. Install A/C compressor fan to crankshaft pulleyV-belt

34. Install cylinder head cover sub-assembly.

(a) Wipe off all seal packing material.

(b) Apply the seal glue on cylinder head cover as shown in Figure 48.

(d) Install cylinder head cover with 4 seal gaskets and 4 nuts.

Torque: 7.8N. M

(e) Install 2 ventilation hoses onto cylinder head cover.

(f) Install engine wire harness onto cylinder head cover.

(g) Connect generator wire joint.

(h) Connect generator wire.

(i) Connect oil pressure switch connector.

(j) Install wire clip.

(k) Connect A/C compressor switch connector.

35. Hoist the engine back into the compartment

36. Install left & right rear engine mounting brackets

37. Install ignition coil and high pressure cable

38. Install air filter assembly with hose

Figure 48

Figure 46

Figure 47

Содержание CK MR479Q 2007









































































































































































































































































































































































































Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды

Geely CK MR479Q 2007, Руководство по ремонту

Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды