Geely CK MR479Q 2007 Скачать руководство пользователя

Страница: 333 / 392

326

(III) Outside Rear View Mirror

Attach the outside rear view mirror to the left and right doors. Integrate the outside rear view mirror with the

body smoothly using specially designed rubber bushing to make it a whole. The forward and rearward folding

of the rear view mirror will not be affected after being knocked. It is also a major way to reduce the whole

vehicle's air resistance coefficient.

Attach the lens to the plate with double sided adhesive tape. The plate is connected to the rear view mirror

case with the ball hinge to prevent fragment from splashing when it is broken, which may result in injury and

it is convenient to replace the broken lens. Pry the plate from the ball socket with the tool when the lens is

broken for replacement and press the new one into the ball socket. The case overturn force is designed to be

30N, enabling it liable to overturn when impacted by person or object and hence reducing the mutual damage.

The adjust handle of the outside rear view mirror is designed to be built in the vehicle to facilitate the

operator's direction adjustment. The optional flat mirror is generally selected for driver side to ensure the

sense of reality and distance. Spherical mirror is used for front passenger side to enlarge the rear field of

vision. In addition, outside rear view mirror has also the feature of electrical heating and defogging.

Notice

When folding the outside rear view mirror, be careful not to put your finger between the outside

rear view mirror and the mirror foot to avoid being crushed!

Replace the Rear View Mirror

Removal

1. Remove battery negative cable.

2. Remove the inside trim.

3. Disconnect electric outside rear view mirror connector.

4. Remove screw and outside rear view mirror retaining clip.

5. Remove electric outside rear view mirror.

6. The installation is in the reverse order of the removal.

Installation

1. Position the rear view mirror on the door

2. Tighten the screw from left lower side screw clockwise

Tighten

Tighten the outer rear view mirror screw to 1.5 N.M¡«2 N.M

3. Install rear view mirror inside trim cover

4. Install rear view mirror inner adjust handle

Содержание CK MR479Q 2007









































































































































































































































































































































































































Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды

Geely CK MR479Q 2007, Руководство по ремонту

Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды