Geely CK MR479Q 2007 Скачать руководство пользователя

Страница: 386 / 392

379

In order to avoid corroding and effectively extend the service life of the punching parts, galvanized steel

sheet with different specifications is widely adopted on the body (Figure 5-23).

(Figure 5-23) Galvanized Steel Plates

1. LH/RH Mudguard Reinforcement

2 Cowl Upper Baffle

3 Radiator Support

4 LH/RH Front Mudguard

5 LH/RH Front Side Member

6 Front Low Cross Member

7 Rear Floor 2nd Cross Member

8 LH/RH Rear Floor Side Rails 9 LH/RH Floor Side Member Inner

Plate 10 Cowl Lower Cross Member 11. Cowl Panel

2. Vibration Reduction And Sound Insulation

Take measures on the structure of the body

a. Reasonably layout reinforcing ribs to improve the rigidity of parts and to reduce noise by restraining

vibration.

b. Fill the floor joint seam with sealant to strengthen the floor sealing and weaken the noise.

c. Increasing the thickness of the cowl is very effective to insulate sound. The cowl is adopted

sandwich structure, (Figure 5-24) that is, the cowl is welded by two steel plates (Cowl and heat

insulating board), and in the interlayer of the 2 plates lies a heat insulating pad (the material of it is

asphalt piece).

Содержание CK MR479Q 2007









































































































































































































































































































































































































Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды

Geely CK MR479Q 2007, Руководство по ремонту

Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды