Geely CK MR479Q 2007 Скачать руководство пользователя

Страница: 275 / 392

268

Disconnect the positive (+) and negative (-) terminal cables from the battery and remove the battery from

the vehicle.

The airbag assembly shall be deployed according to the following procedures.

(2) Driver airbag assembly

Remove the knee bolster.

Remove the connector (yellow) that connecting the lower end of the clock spring with the wire harness

of the instrument panel (see the figure below).

Tie two 6m plus wire harnesses for deployment to the adaptor wire harness of the airbag, and wrap the

connecting points with insulating tape for insulation. The other ends of the wire harness for deployment

are connected to each other (short circuited). Unexpected deployment resulted from static electricity

shall be prevented.

From the yellow connector of the clock spring, lead the airbag adapter wire harnesses out of the vehicle

by means of the wire harnesses for deployment (see the figure below).

To restrain the noise, close all the windows and doors and put on the vehicle cover.

NOTICE

Work must be started 60s after the positive (+) and negative (-) terminal cables are detached from battery.

NOTICE

Remove the connector of the clock spring from the wire harness of the instrument, the connector will be

short circuited automatically, which can avoid the possible serious accident resulted from the deployment of

the diver airbag assembly due to static electricity.

NOTICE

The glass will likely break up if there is crack. Vehicle covers shall be put on.

Содержание CK MR479Q 2007









































































































































































































































































































































































































Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды

Geely CK MR479Q 2007, Руководство по ремонту

Результаты поиска

Содержание CK MR479Q 2007

Отзывы:

Похожие инструкции для CK MR479Q 2007

Бренды по названию

Популярные бренды