manualshive.com logo in svg

Geehy SEMICONDUCTOR APM32F030x4x6x8xC, Руководство пользователя

Поделиться
Скачать
Geehy SEMICONDUCTOR APM32F030x4x6x8xC Скачать руководство пользователя страница 290

 

www.geehy.com                                                                                                                                              Page  289

 

Field 

Name 

R/W

 

Description

 

I2CEN=0. 

6 

TXCFLG 

R 

Transmit Data Complete Flag 
0: Transmit data is not completed 
1: Transmit data is completed 
This bit can be set to 1 by hardware when RELOADEN=0, ENDCFG=0 
and NUMBYT data have been transmitted; be cleared when START=1 
or STOP=1; or be cleared by hardware when I2CEN=0. 

7 

TXCRFLG 

R 

Transfer Complete Reload Flag 
0: Transmission is completed 
1: Transmission is completed to reload 
This bit can be set to 1 by hardware when RELOADEN=1 and NUMBYT 
data have been transmitted; it can be cleared by software by writing a 
non-zero value to NUMBYT; or be cleared by hardware when I2CEN=0. 
This bit works only in master mode, or in slave mode when SBCEN=1. 

8 

BERRFLG 

R 

Bus Error Flag 
0: No bus error 
1: Bus error occurred 
This bit can be set to 1 by hardware when wrong start bit or stop bit is 
detected; be cleared by software by setting BERRCLR bit; or be cleared 
by hardware when I2CEN=0. 

9 

ALFLG 

R 

Arbitration Lost Flag 
0: No arbitration loss 
1: Arbitration loss occurred 
This bit can be set to 1 by hardware when bus arbitration loss occurs; be 
cleared by software by setting ALCLR bit; or be cleared by hardware 
when I2CEN=0. 

10 

OVRURFLG 

R 

Overrun/Underrun Flag 
0: No overrun/underrun 
1: Overrun/Underrun occurs 
This bit can be set to 1 by hardware if overrun/underrun error occurs in 
slave mode when CLKSTRETCHD=1; be cleared by software by setting 
OVRURCLR bit; and be cleared by hardware when I2CEN=0. 

11 

PECEFLG 

R 

PEC Error in Reception Flag 
0: No PEC error 
1: PEC error occurs 
This bit can be set to 1 by hardware when the received PEC value does 
not match the value of PEC register. A NACK will be transmitted 
automatically when wrong PEC is received. This bit can be cleared by 
software by setting PECECLR bit; and be cleared by hardware when 
I2CEN=0. If SMBus mode is not supported, this bit will be reserved and 
be forced to 0 by hardware. 

12 

TTEFLG 

R 

Timeout or Tlow Error Flag 
0: No timeout error 
1: Timeout error occurs 
This bit can be set to 1 by hardware when timeout or external clock 
timeout occurs; be cleared by software by setting TTECLR bit; and be 
cleared by hardware when I2CEN=0. If SMBus mode is not supported, 
this bit will be reserved and be forced to 0 by hardware. 

13 

SMBALTFLG 

R 

SMBus Alert Occur Flag 
0: No SMBus alarm 
1: SMBus alarm occurred 
This bit can be set to 1 by hardware if HADDREN=1 (configured by 
SMBus HOST) and ALTEN=1, and SMBALERT falling edge is detected 
on SMBALERT pin; be cleared by software by setting SMBALTCLR bit; 
and be cleared by hardware when I2CEN=0. If SMBus mode is not 
supported, this bit will be reserved and be forced to 0 by hardware. 

14 

Reserved 

15 

BUSBSYFLG 

R 

Bus Busy Flag 
0: The bus is idle (no communication) 

Содержание APM32F030x4x6x8xC












































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды