manualshive.com logo in svg

GE H49021AA, Базовое руководство по обслуживанию

Базовый сервисный мануал для GE H49021AA теперь доступен для бесплатного скачивания на нашем сайте. Этот руководство поможет вам разобраться с вашим устройством более эффективно. Просто перейдите на manualshive.com и загрузите его сейчас.

Поделиться
Скачать
background image

GE M

EDICAL

 S

YSTEMS

 

D

IRECTION

 5184024-100, R

EVISION

 5

LOGIQ

WORKS

® B

ASIC

 S

ERVICE

 M

ANUAL

 

Chapter 2 Pre-Installation

2-9

2-2-5

EMI Limitations

Computers are susceptible to Electromagnetic Interference (EMI) from radio frequencies, magnetic 
fields, and transients in the air or wiring. They also generate EMI. The LOGIQworks complies with limits 
as stated on the EMC label. However there is no guarantee that interference will not occur in a particular 
installation.

Possible EMI sources should be identified before the unit is installed. 

Electrical and electronic equipment may produce EMI unintentionally as the result of a defect. 
These sources include: 

•

medical lasers, 

•

scanners, 

•

cauterizing guns, 

•

computers, 

•

monitors, 

•

fans, 

•

gel warmers, 

•

microwave ovens,

•

light dimmers 

•

portable phones. 

The presence of a broadcast station or broadcast van may also cause interference.

see 

Table 2-16

 for EMI Prevention tips

 

WARNING

WARNING

Danger of Electromagnetic Incompatibility!

Devices that are not CE marked can create an electromagnetic field which could impair the operation 
of other devices.

To prevent this, check if the device is CE marked or FCC-marked.

Use only CE marked devices and medical devices appropriate under 
EN/IEC 60601-1-2.

WARNING

WARNING

Danger of False Diagnosis!
Danger of Data Loss!

Personal computers can be affected by electromagnetic fields from other devices.

Do not place devices which could cause electromagnetic interference near the personal computer!

Table 2-16    EMI Prevention/Abatement

EMI Rule

Details

Be aware of RF sources

Keep the unit at least 5 meters or 15 feet away from other EMI sources. Special shielding may 
be required to eliminate interference problems caused by high frequency, high powered radio 
or video broadcast signals.

Ground the unit

Poor grounding is the most likely reason a unit will have noisy images. Check grounding of the 
power cord and power outlet.

Содержание H49021AA





































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H49021AA

Ecco 200 Series Installation & Operating Instructions preview
200 Series
Бренд: Ecco Страницы: 4
JD Squared 3 Assembly & Operating Instructions preview
3
Бренд: JD Squared Страницы: 15
DAPAudio D1256 Manual preview
D1256
Бренд: DAPAudio Страницы: 16
3M 400 Series User Instructions preview
400 Series
Бренд: 3M Страницы: 28
DARKSTAR TECHNOLOGIES D340 Manual To Operation preview
D340
Бренд: DARKSTAR TECHNOLOGIES Страницы: 4
TDW D2000 Maintenance Manuallines preview
D2000
Бренд: TDW Страницы: 2
Taurus 1170 Assembly And Operating Instructions Manual preview
1170
Бренд: Taurus Страницы: 25
Vancare G Series Quick Reference Manual preview
G Series
Бренд: Vancare Страницы: 3
Paitec ES-2000 User Manual preview
ES-2000
Бренд: Paitec Страницы: 14
BANDELIN Sonopuls HD 4050 User Instructions preview
Sonopuls HD 4050
Бренд: BANDELIN Страницы: 48
Ecler MIMO4040CDN Service Manual preview
MIMO4040CDN
Бренд: Ecler Страницы: 108
R&S RTE Getting Started preview
RTE
Бренд: R&S Страницы: 121
Rath 2100-VOIP2CS Installation & Operation Manual preview
2100-VOIP2CS
Бренд: Rath Страницы: 5
Radian Heart Guardian AED User Manual preview
Heart Guardian AED
Бренд: Radian Страницы: 36
Rational UltraVent XS Plus 6 2/3 E Original Installation Manual preview
UltraVent XS Plus 6 2/3 E
Бренд: Rational Страницы: 220
zapco AGSP4-SL Owner'S Manual preview
AGSP4-SL
Бренд: zapco Страницы: 14
Rigol RP1010H User Manual preview
RP1010H
Бренд: Rigol Страницы: 12
Ground Fault Systems DGF100 Manual preview
DGF100
Бренд: Ground Fault Systems Страницы: 26

Бренды по названию

Популярные бренды

Загрузить еще бренды