manualshive.com logo in svg

GE H49021AA, Базовое руководство по обслуживанию

Базовый сервисный мануал для GE H49021AA теперь доступен для бесплатного скачивания на нашем сайте. Этот руководство поможет вам разобраться с вашим устройством более эффективно. Просто перейдите на manualshive.com и загрузите его сейчас.

Поделиться
Скачать
background image

GE M

EDICAL

 S

YSTEMS

D

IRECTION

 5184024-100, R

EVISION

  5

LOGIQ

WORKS

® B

ASIC

 S

ERVICE

 M

ANUAL

 

1-6

Section 1-2 - Important Conventions

1-2-3

Product Icons

The following table describes the purpose and location of safety labels and other important information 
provided on the equipment.

Table 1-8

   Product Icons 

LABEL/SYMBOL

PURPOSE/MEANING

LOCATION

Identification and Rating Plate

Manufacturer's name and address

Model and serial numbers

Electrical ratings

On top of PC

Device Listing/Certification Labels

Laboratory logo or labels denoting 
conformance with industry safety standards 
such as UL or IEC.

Rear side of the unit

Rear side of the monitor

Type/Class Label

Used to indicate the degree of safety or protection.

“CAUTION

This unit weighs...

Special care must be used to avoid..."

This precaution is intended to prevent injury 
that may result if one person attempt to move 
the unit considerable distances or on an incline 
due to the weight of the unit.

Service Manual

"CAUTION" The equilateral triangle is usually 
used in combination with other symbols to 
advise or warn the user.

Various

ATTENTION - Consult accompanying 
documents " is intended to alert the user to 
refer to the operator manual or other 
instructions when complete information cannot 
be provided on the label.

Various

"CAUTION - Dangerous voltage" (the lightning 
flash with arrowhead in equilateral triangle) is 
used to indicate electric shock hazards.

Various

"Mains OFF" Indicates the power off position of 
the mains power switch.

ON/OFF switches

Содержание H49021AA





































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для H49021AA

KaVo 4040 Operating, Maintenance And Assembly Instructions preview
4040
Бренд: KaVo Страницы: 16
M-Audio MidAir 25 User Manual preview
MidAir 25
Бренд: M-Audio Страницы: 25
Nederman RBU 1300 User Manual preview
RBU 1300
Бренд: Nederman Страницы: 255
OHAUS Guardian 2000 Instruction Manual preview
Guardian 2000
Бренд: OHAUS Страницы: 84
GE PWS Operating And Maintenance Instructions Manual preview
PWS
Бренд: GE Страницы: 18
Barreto HT712 Operator'S Manual preview
HT712
Бренд: Barreto Страницы: 16
EuroLite SBPO-3240 Installation Instructions preview
SBPO-3240
Бренд: EuroLite Страницы: 2
B medical systems MRB 3000 SDD Instructions For Use Manual preview
MRB 3000 SDD
Бренд: B medical systems Страницы: 28
Nautilus NT 1800 Assembly Manual preview
NT 1800
Бренд: Nautilus Страницы: 2
Harken Ti-Lite Carbo AirBlock 351 Instructions preview
Ti-Lite Carbo AirBlock 351
Бренд: Harken Страницы: 2
Fillauer ALP Aluminum Product Manual preview
ALP Aluminum
Бренд: Fillauer Страницы: 12
Hoshizaki RM-45-SD Service Manual preview
RM-45-SD
Бренд: Hoshizaki Страницы: 35
lumishore EOS Mini Manual preview
EOS Mini
Бренд: lumishore Страницы: 13
Rainbow Colour Changers 8-Lite Plus Operator'S Manual preview
8-Lite Plus
Бренд: Rainbow Colour Changers Страницы: 22
Protech Machinery P200S Operator And Parts Manual preview
P200S
Бренд: Protech Machinery Страницы: 21
TOORX MSX-70 Instruction Manual preview
MSX-70
Бренд: TOORX Страницы: 28
Erbe 20150-020 Notes On Use preview
20150-020
Бренд: Erbe Страницы: 154
Rottler S7M Operation And Maintenance Manual preview
S7M
Бренд: Rottler Страницы: 96

Бренды по названию

Популярные бренды

Загрузить еще бренды