GE GL 311 F3/4031 P/VE Скачать руководство пользователя страница 66

Страница: 66 / 146

ROUBLESHOOTING

66 / 146

OI 250 (EN)

REV7

/REV2

8.2

Mechanism Reconditioning Procedures

8.2.1

Replacing the Charging Motor

• Disconnect both wires from the motor limit switch.

• Unscrew the M6 mounting screws and remove the motor.
• Install the new motor and tighten the mounting screws to a torque

of 7Nm.

• Reconnect the wires to the motor limit switch.

Lubrication of the motor pinion may cause the operating
mechanism to malfunction.
Do not grease or lubricate the motor pinion.

CAUTION

If the wiring is incorrect, the motor will stall and may become
damaged.
Turn on the power to the motor briefly and check to see whether
the motor drives the gear unit.

If this is not the case:
- Turn off the power to the motor immediately.
- Check the connections and correct if necessary.

CAUTION

Содержание GL 311 F3/4031 P/VE



















































































































































Результаты поиска

Содержание GL 311 F3/4031 P/VE

Отзывы:

Похожие инструкции для GL 311 F3/4031 P/VE

Бренды по названию

Популярные бренды

GE GL 311 F3/4031 P/VE, Руководство по эксплуатации

Результаты поиска

Содержание GL 311 F3/4031 P/VE

Отзывы:

Похожие инструкции для GL 311 F3/4031 P/VE

Бренды по названию

Популярные бренды