GE GL 311 F3/4031 P/VE Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 146

background image

C

OMMISSIONING

OI 250 (EN)

REV7

/REV6

7.4

Checking the Anti-Condensation Heater

Measure the resistance of the anti-condensation heater at the ter-
minals in the operating mechanism and compare it with the refe-
rence value in the routine test certificate. Enter the values in the
checklist.

7.5

Connecting the Supply and Control Cables

• Insert the supply and control cables through the cable entry plate

on the underside of the operating mechanism. This plate must be
fitted with cable glands by the station (and can be removed for
repairs or maintenance). Connect the cables in accordance with
the schematic diagram.

Serious personal injury or property damage can result during
commissioning if the equipment is live or energized.

Therefore:
- Make sure the supply and control cables are not live be-

fore connecting them.

WARNING

The mechanism's charging process will begin immediately after
the supply and control voltages are connected.

Therefore:
- Keep parts of the body and other objects away from the

moving parts of the operating mechanism and the entire
connecting linkage.

WARNING

The anti-condensation heater will heat up after the supply and
control voltages are connected. Touching the anti-condensation
heater can result in burns.

Therefore:
- Do not touch the anti-condensation heater.

CAUTION

«
...
56
57
58
59
60
...
»

Содержание GL 311 F3/4031 P/VE



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для GL 311 F3/4031 P/VE

DUSPOL expert 1000

Бренд: Gossen MetraWatt Страницы: 6

Бренд: Bticino Страницы: 4

Бренд: ABB Страницы: 17

Бренд: Eaton Страницы: 25

Бренд: ABB Страницы: 72

Бренд: Schrack Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды