GE GL 311 F3/4031 P/VE Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 146

background image

T

RANSPORT

AND

S

TORAGE

OI 250 (EN)

REV7

/REV1

The wood used for the packaging may be chemically or thermally
treated in order to prevent the spread of wood pests. Related rules
and markings are defined in U.N. International Plant Protection
Convention (IPPC) guidelines.

5.2

Storage

The transport unit packaging is only designed for a limited storage
period.

The following periods, figured from the shipping date, shall apply to
storage in transport packaging:
- Storage outdoors: four months maximum
- Storage in a dry room: six months maximum.

The following periods and conditions shall apply to storage after
unpacking:
- Storage outdoors: unlimited. The operating mechanism must be

in the mounting position, and the anti-condensation heating unit
must be connected and in operation.

- Storage in a dry room: unlimited.

IPPC-Symbol:
Treated wood
packaging

Depending on the transport conditions, the operating mechanism
may be wrapped and sealed in sheet or foil. This prevents
penetration of moisture.
If the sheet or foil is damaged, the operating mechanism must be
stored as described above.

CAUTION

«
...
18
19
20
21
22
...
»

Содержание GL 311 F3/4031 P/VE



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для GL 311 F3/4031 P/VE

Бренд: dehn Страницы: 24

SureTest 61-164

Бренд: IDEAL Страницы: 24

Бренд: Eaton Страницы: 34

Бренд: NSS Страницы: 4

DILMS40-DILMS65 Series

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: FEDERAL PACIFIC Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды