GE GL 311 F3/4031 P/VE Скачать руководство пользователя страница 61

Страница: 61 / 146

OMMISSIONING

REV7

/REV6

OI 250 (EN)

61 / 146

7.6.5

Checking Manual Operation

The manual operating levers are protected against accidental ope-
ration by a locking plate.

• Loosen the locking bolts (1) one full turn and push the locking

plate (2) down and to the left.

• Carry out one closing operation and one opening operation using

the manual operating levers. The circuit breaker will immediately
carry out the corresponding operation.

• Push the locking plate up and to the right, and tighten the two

locking bolts again.

Manual operation bypasses any circuit breaker interlock system.

Therefore:
- Make sure that the gas pressure in the circuit breaker cor-

responds at least to the UW2 value before beginning ma-
nual operation.

WARNING

Locking bolt

Locking plate

Manual operation for closing operation

Manual operation for opening operation

-P

-HA

NDS

RRE

Содержание GL 311 F3/4031 P/VE



















































































































































Результаты поиска

Содержание GL 311 F3/4031 P/VE

Отзывы:

Похожие инструкции для GL 311 F3/4031 P/VE

Бренды по названию

Популярные бренды

GE GL 311 F3/4031 P/VE, Руководство по эксплуатации

Результаты поиска

Содержание GL 311 F3/4031 P/VE

Отзывы:

Похожие инструкции для GL 311 F3/4031 P/VE

Бренды по названию

Популярные бренды