GE ApexPro Скачать руководство пользователя страница 137

Страница: 137 / 218

Viewing real-time patient data

2001989-200E

ApexPro™

7-29

Complete the following procedure to adjust the control settings.

From the multi-patient viewer, click on the patient you want to view. The single
patient viewer displays.

From the single patient viewer, click

Monitor Setup

Click

Pressures

to display the control window.

Change any of the undimmed setting options.

065A

After making your selections, complete one of the following tasks:

Non-invasive blood pressure control settings

Option

Function

Auto

Turn

Off

automatic NBP measurements.

When turned

at the monitor, NBP measurements are

acquired automatically at regular intervals.

NOTE

This option does not apply to telemetry beds and
cannot be turned on from the CIC Pro center.

Cuff Size

Set the inflation pressure used during the first NBP
measurement and for calculating the NBP pressure:

NOTE

For more information, refer to the appropriate
bedside monitor’s operator’s manual.

NOTE

Cuff size cannot be changed on telemetry beds.

Clear Message

button

Clear the display of inflation messages and current NBP
readings.

Содержание ApexPro



























































































































































































































Результаты поиска

Содержание ApexPro

Отзывы:

Похожие инструкции для ApexPro

Бренды по названию

Популярные бренды

GE ApexPro, Руководство оператора

Результаты поиска

Содержание ApexPro

Отзывы:

Похожие инструкции для ApexPro

Бренды по названию

Популярные бренды