GE ApexPro Скачать руководство пользователя страница 202 | Manualshive

Страница: 202 / 218

background image

D-8

ApexPro™

2001989-200E

Troubleshooting

Messages

Alarm messages

The following messages appear in the patient’s bed window at the CIC Pro center.

CHANGE BATTERY

An NBP measurement was attempted with low batteries. Change the batteries in
the blood pressure monitor and try another measurement.

FAIL

A hardware failure has been detected in the blood pressure monitor. In the U.S.,
contact GE Service. Outside the U.S., contact your local sales/service
representative.

LEAK

The NBP cuff is loose or there is an air leak in the cuff or tubing. Check that the
cuff is on snugly. Check the connection between the cuff and the tubing. Check
the connection between the tubing and the blood pressure monitor. Try another
measurement. If the problem persists, contact your local sales/service
representative.

LOW INFLATION PRESS

This message appears when K-sounds are detected immediately upon inflation.
The inflation pressure is too low for proper NBP measurement. Try another
measurement or adjust dynamic/fixed inflate. If the problem persists, contact your
local sales/service representative.

MOVEMENT

This message appears when there is excessive patient arm movement, or if the
patient’s arm was bent during the measurement. Check the patient and try
another measurement.

SENSOR?

This message appears when the K-sounds on the measurement were too weak,
or not enough sounds were detected. Reposition the microphone and try another
measurement. This message can also appear if the deflate rate is not properly
adjusted. If the problem persists, contact your local sales/service representative.

WEAK PULSE

The patient’s heart rate is erratic. Check that the microphone cable is plugged
firmly into the patient cable, and check that the microphone is positioned correctly
on the patient. Try another measurement. If the problem persists, it could indicate
a defective microphone, microphone cable, or patient cable. Contact your local
sales/service representative.

ALARM PAUSE

All alarms for this patient have been turned off for five
minutes. This is initiated from the transmitter by pressing
both the

Verify Leads

and

Graph

buttons simultaneously.

See Pausing alarms at the transmitter on page 5-5.

ALL ALARMS OFF

All alarms for this patient have been turned off. No graph
strips run, arrhythmia events are not stored, and no audible
tones sound if an alarm condition should occur.

ARR OFF

The arrhythmia program for a selected patient has been
turned off. No arrhythmia messages are displayed,
arrhythmia event s are not stored, no graph strips run, and no
audible tones sound if an arrhythmia alarm condition occurs.

«
...
200
201
202
203
204
...
»

Содержание ApexPro



























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ApexPro

Бренд: Labnet Страницы: 5

Бренд: XTA Страницы: 29

Бренд: vc999 Страницы: 59

Бренд: Qtx Страницы: 3

Бренд: Saferoad Страницы: 24

Бренд: Tascam Страницы: 27

Бренд: Jay-Lor Страницы: 72

Бренд: MacDon Страницы: 198

Бренд: M-Triangel Страницы: 6

Бренд: JB Systems Страницы: 7

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 36

Бренд: 3A HEALTH CARE Страницы: 16

Short/cut 2000 Audio Editor

Бренд: 360 Systems Страницы: 4

Бренд: Tascam Страницы: 128

Бренд: ParaBody Страницы: 6

Sportsound SSR-300

Бренд: Daktronics Страницы: 42

Бренд: Eagle Eye Страницы: 21

Бренд: Labomed Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды