GE ApexPro Скачать руководство пользователя страница 74

Страница: 74 / 218

5-6

ApexPro™

2001989-200E

Alarms

After five minutes, the LED on the transmitter will no longer flash and alarms will be
reactivated.

Reactivating alarms at the transmitter

To reactivate the alarms before the five minute time period has elapsed, press both
transmitter buttons simultaneously again.

Alarm pause breakthrough

NOTE

For more information on the

Alarm Pause Breakthrough

feature in

Combo

mode, refer to

Combo and Rover Combo monitoring on page 6-19

NOTE

The

Alarm Pause Breakthrough

feature defaults to

Always On

. It can be set to

Always

Off

in the

Telemetry Unit Defaults

tab (in service mode only) sheet

BEFORE admitting a telemetry patient if you do not wish to have

Crisis

level

alarms break through alarm pauses.

This feature cannot be set on an individual patient basis. It is either on or off for
all telemetry patients admitted to the CIC Pro center. A status message on each
patient’s

Alarm Control

tab sheet indicates whether it is enabled (on) or disabled

(off).

The

Alarm Pause Breakthrough

feature allows any

Crisis

level alarm to break

through (interrupt) an alarm pause and sound at the CIC Pro center.

In other words, when this feature is turned on in the

Telemetry Unit Defaults

tab

sheet,

Crisis

level alarms will sound at the CIC Pro center, even if an alarm pause is in

effect.

The chart below illustrates the function of the

Alarm Pause Breakthrough

feature

during the various alarm states.

After a

Crisis

level alarm has broken through an alarm pause, the telemetry system

does

not

return to an alarm pause state. All alarms at any alarm level will sound at the

CIC Pro center.

If you wish to continue pausing alarms after an

Alarm Pause Breakthrough

occurs,

you must re-initiate the alarm pause:

Alarm Pause State

Alarm Pause Breakthrough Feature Enabled

Alarms on

Alarm Pause Breakthrough

; all alarms are on.

Alarms off

Alarm Pause Breakthrough

; all alarms are off.

Alarm off reason (X-ray,
shower, etc.)

Alarms are paused;

Crisis

level alarms will break through

the alarm off reason if the patient is in antenna range.

Alarms paused from the
transmitter

Alarms are paused;

Crisis

level alarms will break through

the alarm pause.

Содержание ApexPro



























































































































































































































Результаты поиска

Содержание ApexPro

Отзывы:

Похожие инструкции для ApexPro

Бренды по названию

Популярные бренды

GE ApexPro, Руководство оператора

Результаты поиска

Содержание ApexPro

Отзывы:

Похожие инструкции для ApexPro

Бренды по названию

Популярные бренды