GBC Explorer 107 Скачать руководство пользователя страница 92

Страница: 92 / 130

Page 5 - 26

Explorer 107 Operation and Maintenance Manual

Operations

© GBC Pro - Tech December 1999

b) Raise the safety shield to its full up right

position.

c) Pull the two locator latches of the pressure

plate toward the center of the laminator.

Locator latches

d) Remove the pressure plate and set in a safe

place away from the laminator if not used.

Replacing the pressure plate

a) Pull the two locator latches of the pressure

plate towards the center and position so the
locator latch pins align with thier respective
holes.

b) Pull both safety latches on the front safety

shield toward the center of the laminator
and lower.

c) Align the safety latches with thier respective

interlocks and slide the safety latches
outwards.

INFORMATION

The laminator will operate only when

all safety latches are in the fully

latched position.

5.10 Feed table

The feed table is equipped with a safety latch

and an interlock. These safety devices are in place
for your protction and at no time should they be
over ridden.

D A N G E R

At no time should you attempt to over ride

any of the safety devices on the laminator.

Содержание Explorer 107



































































































































Результаты поиска

Содержание Explorer 107

Отзывы:

Похожие инструкции для Explorer 107

Бренды по названию

Популярные бренды

GBC Explorer 107, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Explorer 107

Отзывы:

Похожие инструкции для Explorer 107

Бренды по названию

Популярные бренды