GBC Explorer 107 Скачать руководство пользователя страница 27

Страница: 27 / 130

Page 1 - 13

Safety

Explorer 107 Operation and Maintenance Manual

© GBC Pro - Tech December 1999

Keep hands and fingers away from the

path of the rear cut-off blade.

Sharp blade can cut you!

W A R N I N G

Keep hands and fingers away from the

bottom of the rear cut-off blade.

Sharp blade can cut you!

W A R N I N G

D A N G E R

At no time should you attempt to over ride

any of the safety latches on the laminator.

INFORMATION

The laminator will operate only when

all safety latches are in the fully

latched position.

INFORMATION

Locator latches on the pressure plate are

not associated with an interlock switch.

The laminator will operate without

the pressure plate installed.

1.5 Applications

The following symbols are positioned at various

points in Section 6 Applications.

W A R N I N G

Do not wear ties, loose fitting clothing or

dangling jewelry while operating or

servicing the laminator. These items can get

caught in the nip and choke you or you can

be crushed or burned.

INFORMATION

Proceed to Webbing while waiting for the

heaters to come up to temperature.

Содержание Explorer 107



































































































































Результаты поиска

Содержание Explorer 107

Отзывы:

Похожие инструкции для Explorer 107

Бренды по названию

Популярные бренды

GBC Explorer 107, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Explorer 107

Отзывы:

Похожие инструкции для Explorer 107

Бренды по названию

Популярные бренды