GBC Explorer 107 Скачать руководство пользователя страница 90

Страница: 90 / 130

Page 5 - 24

Explorer 107 Operation and Maintenance Manual

Operations

© GBC Pro - Tech December 1999

5.8 Front safety shield

The primary function of the front safety shield

is to protect the operator from the heated components
and the nip of the rollers.

The second function of the front safety shield

is to assist the heating components maintain a stable
temperature and keep dust away from the activated
adhesive.

D A N G E R

At no time should you attempt to over ride

any of the safety latches on the laminator.

Caution should always be exercised

when using the laminator with

the safety shields raised.

You can be seriously HURT or INJURED!

W A R N I N G

INFORMATION

The laminator will operate only when

all safety latches are in the fully

latched position.

Raise the shield

a) Pull both safety latches on the front safety

shield toward the center of the laminator.

Safety latches

Caution should always be exercised

when using the laminator with

the safety shields raised.

You can be seriously HURT or INJURED!

W A R N I N G

b) Raise the safety shield to its full up right

position.

Содержание Explorer 107



































































































































Результаты поиска

Содержание Explorer 107

Отзывы:

Похожие инструкции для Explorer 107

Бренды по названию

Популярные бренды

GBC Explorer 107, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Explorer 107

Отзывы:

Похожие инструкции для Explorer 107

Бренды по названию

Популярные бренды