GBC Explorer 107 Скачать руководство пользователя страница 30

Страница: 30 / 130

Page 1 - 16

Safety

Explorer 107 Operation and Maintenance Manual

© GBC Pro - Tech December 1999

Excessive brake tension may cause the

output to curl. Always use the minimum

brake tension required to complete the task.

INFORMATION

The laminator will operate only when

all safety latches are in the fully

latched position.

CAUTION

Never leave the rollers in the down position

without rolling. Prolonged contact in one

area can form flat spots on the rollers.

INFORMATION

The laminator must be heated for this

method of webbing.

W A R N I N G

The following steps are performed while

the laminator is HOT! Avoid contact

with the heating components!

CAUTION

Do not use an open blade to cut

the web near the rollers.

You can put cuts into the rollers!

INFORMATION

The laminator will operate only when

all safety latches are in the fully

latched position.

Keep hands and fingers away from the

path of the rear cut-off blade.

Sharp blade can cut you!

W A R N I N G

Содержание Explorer 107



































































































































Результаты поиска

Содержание Explorer 107

Отзывы:

Похожие инструкции для Explorer 107

Бренды по названию

Популярные бренды

GBC Explorer 107, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Explorer 107

Отзывы:

Похожие инструкции для Explorer 107

Бренды по названию

Популярные бренды