GBC Explorer 107 Скачать руководство пользователя страница 19

Страница: 19 / 130

Page 1 - 5

Safety

Explorer 107 Operation and Maintenance Manual

© GBC Pro - Tech December 1999

CAUTION

Do not use a knife or other sharp object to

remove the shrink wrap from around the

laminator. You can cause irreparable

damage to the rollers.

W A R N I N G

Do not attempt to move the laminator across

anything other than a flat level surface

without trained and qualified riggers. You

can be crushed or seriously injured.

CAUTION

Do not allow the top to fall into the crate. It

can damage the laminator.

INFORMATION

Do not put packing screws on the floor.

They can cause problems when trying to roll

the laminator into position or you can

become injured if stepped on.

CAUTION

A second person must support the side
labeled 5 in Figure 4.4.1 It can fall and

damage the laminator or cause harm to you

and others.

GBC Pro-Tech's warranty does not cover

malfunction of the equipment due to

mishandling and / or tipping. GBC Pro-

Tech bears no responsibility for personal

injury or damage due to moving the

laminator improperly.

INFORMATION

About recycling: The crate components can

be reused for shipping the laminator again

or can be disassembled and the wood and

screws recycled. The shrink wrap is not

recyclable, so it must be discarded.

INFORMATION

W A R N I N G

Do not wear ties, loose fitting clothes or

dangling jewelry while operating or

servicing the laminator. These items can get

caught in the nip and choke you or you can

be crushed or burned.

Содержание Explorer 107



































































































































Результаты поиска

Содержание Explorer 107

Отзывы:

Похожие инструкции для Explorer 107

Бренды по названию

Популярные бренды

GBC Explorer 107, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Explorer 107

Отзывы:

Похожие инструкции для Explorer 107

Бренды по названию

Популярные бренды