WARNING: For your protection do not connect the
Laminator to electrical power or attempt to
operate until you read these instructions
completely. Keep these instructions in a
convenient location for future reference. To
guard against injury, the following basic safety
precautions must be observed in the set-up
and use of the laminator.
Set-up
1. Connect power cord to appropriate power source.
2. Push the switch on to ÔWARMÕ.
3. Select appropriate temperature for both gauge of pouch you
are using and the type of material you are laminating (see
chart for guidelines).
Approximate temperature setting guidelines for pouches*
*
Temperature setting will vary due to the finish, chemistry
and heat absorption properties of the materials you are
laminating. Use this chart as a guideline only and adjust
temperature as necessary. If pouch is cloudy the first pass
through the machine, adjust temperature setting higher and
run through again. If warping occurs, reduce temperature -
run additional pieces at lower setting once machine has
cooled.
Operation
1. Once the ÔREADYÕ light activates to indicate machine is at
operating temperature, switch machine on to ÔRUNÕ.
2. Place the item to be laminated into a laminating pouch,
centring it within the pouch (see figure 1).
3. Insert the pouch containing the item into a carrier which is
provided with each carton of pouches. Position the pouch
toward the centre of the carrier with the sealed edge facing
the inside folded edge of the carrier (see figure 1). Please
handle carriers carefully so they may be re-used.
4. Insert the folded edge of the carrier STRAIGHT into the
front of the laminator until you feel the roller pick up the
carrier.
5. Remove the carrier from the rear of the laminator after it
has stopped moving. Leave the pouch within the carrier
and place on a flat surface for a few seconds until cool
before removing it.
6. If you adjust the temperature during a lamination job, allow
appropriate time for the machine to reach desired
temperature.
Guidelines
Wait a few minutes then verify the
temperature with the ÔREADYÕ
light.
Wait at least 10 minutes
7. When you are finished laminating, switch the machine to
ÔOFFÕ.
Note:
The laminator features an AUTO cut-off to prevent
overheating. If this should occur, allow unit to cool
before continuing your lamination application. If you are
laminating using 500 micron pouches please be aware
Auto cut-off will occur after 15 minutes. In the event,
allow unit to cool before you continue with your
lamination application.
General safeguards
Use the laminator only for its intended purpose of laminating
documents up to 292mm wide.
Do not place anything in the throat opening of the machine
other than pouch carriers with appropriate pouches inside.
Place unit on a secure, stable work area to prevent the
machine falling and possibly causing personal injury and/or
damage to the unit.
Turn unit off when not in use.
Electrical safeguards
The laminator must be connected to a supply voltage
corresponding to the electrical rating of the machine as
indicated on the serial label located on the base.
Unplug the laminator before moving it, or when it is not in
use for an extended period of time.
Compact A3 Laminator
Stock No. 184-5236
Pouch
(total thickness)
Heat setting Heat setting Heat setting
70gsm paper 80gsm paper 135gsm
artpaper
(colour printed)
A3
150 micron
3.0
3.0
3.0
250 micron
3.5
3.5
3.5
360 micron
4.0
4.0
4.0
500 micron
4.0
4.0
4.5
A4
150 micron
2.5
3.0
3.0
250 micron
3.5
3.5
3.5
360 micron
4.0
4.0
4.0
500 micron
4.0
4.0
4.5
ID
250 micron
3.5
3.5
3.5
360 micron
4.0
4.0
4.0
500 micron
4.5
4.5
4.5
NB: Not recommended for use on photographs
* Raise temperature
to a higher setting
* Reduce temperature
to a lower setting
Figure 1.
¥
¥
¥
¥
¥
¥
