manualshive.com logo in svg

Gateway E-842R, Руководство пользователя

Поделиться
Скачать
Gateway E-842R Скачать руководство пользователя страница 139

List of events

www.gateway.com

133

Temperature sensor <

zz>

 is 

in a critical state. 
(continued)

Error
[0xC6D 
(3181)]

Temperature sensors 
are reporting 
enclosure 
temperatures have 
reached the threshold 
of 70°C.

If the environment 
ambient temperature 
is high, reduce the 
ambient temperature.
Ensure that the airflow 
is not blocked or 
restricted on the 
enclosure.

Alarm is Off (Muted).

Information
[0xC6E 
(3182)]

No condition being 
reported.
Alarm silenced.

No action necessary.
User pressed the Alarm 
Mute button on the 
Ops panel.

Alarm is Intermittent. 

Error
[0xC6E 
(3182)]

A condition caused the 
alarm to sound every 
two minutes until 
muted.

Press the Alarm Mute 
button on the Ops 
panel and isolate the 
cause of the alarm.

Alarm is Remind. 

Error
[0xC6E 
(3182)]

A condition that 
caused the alarm to 
sound is continuing to 
remind the user.

Press the Alarm Mute 
button on the Ops 
panel and isolate the 
cause of the alarm.

Alarm is On Continuous. 

Error
[0xC6E 
(3182)]

A condition caused the 
alarm to sound.

Press the Alarm Mute 
button on the Ops 
panel and isolate the 
cause of the alarm.

SES access fault tolerant: 
Multiple paths are available 
for gathering this 
enclosure’s status 
information. 

Information
[0xCFD 
(3325)]

An enclosure is now 
SES fault-tolerant.

No action necessary.

SES access not fault 
tolerant: If this enclosure’s 
SES enabled drive fails then 
no information about the 
status of this enclosure is 
available. 

Warning
[0xCFE 
(3326)]

An enclosure was 
found to have only one 
available SES drive.

Press the Alarm Silence 
button on the front 
panel.
Make sure that both 
slot 1 and 7 have SES 
compatible drives 
installed.
Make sure that the SES 
drives installed in slots 
1 and 7 are 
operational.

Enclosure Event Messages

Type [ID]

Cause

Action

Содержание E-842R





































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды