Garmin Cessna Caravan G1000 страница 77 Скачать руководство пользователя | Manualshive

Страница: 77 / 288

background image

______________________________________________________________________________

____________________________________________________________________________

LMM for the Kodiak 100

Page 3-27

190-02102-00 Rev.4

3.9.1 System Communication Hierarchy

The following criteria must be satisfied to be able to perform these desired operations:

3.10 Maintenance Records

After conducting a functional test in accordance with the Kodiak 100 Aircraft Mainte-
nance Manual, the aircraft may be returned to service. Record the following information
in appropriate aircraft maintenance logs:

• Part number of the G1000 NXi Kodiak 100 Loader Card used to perform software

loading or software updates.

• Part numbers and versions of LRU software files reported after maintenance is

complete (found at the System Status page in configuration mode).

Table 3-5. System COM Hierarchy

Desired Operation

Criteria for Success

Load Software to GDU 1050
MFD or PFD Displays.

• G1000 NXi Kodiak 100 Loader Card must be

inserted in top slot for each display to be loaded.

• CLR and ENT keys must be held when system

power is applied to display.

• Power only one display on at a time during soft-

ware loading.

Load Software/Configuration
files to GIA 63/64Ws.

• G1000 NXi system must be powered on.
• PFD and MFD must have correct software.
• PFD and MFD must be successfully configured

with configuration files.

Load Software/Configuration
files to:

• GMA 1347/1360D
• GDC 72
• GEA 71/71B
• GRS 79
• GMU 44/44B
• GTX 345R
• GDL 69A SXM

• G1000 NXi must be powered on.
• G1000 NXi Kodiak 100 Loader Card must be

inserted into PFD top slot.

• PFD and MFD must have correct software and

configuration settings.

• GIA 63/64Ws must have correct software.
• GIA 63/64Ws must be successfully configured with

GIA1 and GIA2 configuration files.

• Serial data path from GIA1 to each LRU must be

operational.

Uncontrolled if Printed

«
...
75
76
77
78
79
...
»

Содержание Cessna Caravan G1000

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cessna Caravan G1000

Stratomaster Enigma

Бренд: MGL Avionics Страницы: 9

Бренд: Garmin Страницы: 142

Бренд: UPS Aviation Technologies Страницы: 11

Бренд: Tecfrigo Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды