manualshive.com logo in svg

Garmin Cessna Caravan G1000, Руководство по линейному обслуживанию

Поделиться
Скачать
Garmin Cessna Caravan G1000 Скачать руководство пользователя страница 112

______________________________________________________________________________

____________________________________________________________________________

Page 4-28

LMM for the Kodiak 100

190-02102-00 Rev.4

4.7.1.2.3   Display is Blank, Resets, or Flickers

1. Cycle power. If the GDU recovers, look for yellow text containing error 

information at the top of the screen. If the message indicates that software needs 
to be reloaded, reload the software. Otherwise, replace the GDU.

2. Shut off all cabin light and hangar lights so the environment is dark, to verify the 

display is just very dim.

3. Adjust the avionics dimmer control fully clockwise.

4. Manually turn up the backlight on the PFD and load configuration files to the 

GDU.

5. Ensure the slide lock is fully engaged with the locking tabs on the back of the unit. 

If the slide lock is not fully engaged, remove the connector and see if the locking 
tabs on the GDU are perpendicular to the connector. If not, straighten them 
before reseating the connector. 

6. Ensure the GDU is receiving power and ground. If a circuit breaker is tripped, find 

the source of short before resetting the breaker. 

7. Verify the circuit breakers have not failed and the power wire connections are 

secure. Troubleshoot the aircraft wiring for faults. 

4.7.1.2.4   SD Card is Stuck in the GDU

1. Do not insert a screwdriver of any length into the card slot.

2. No not pry against the overlay.

3. Do not force the SD card out.

4. Use a small screwdriver in the groove on the side of the exposed end of the card 

to help pull out the card.

5. It might be necessary to push the card in further to release the card locking 

mechanism.

6. If the card can be removed, check for more than one label. Two or more labels on 

the card can cause sticking.

7. Remove all but one label.

8. Ensure the SD card is from SanDisk. Use of other SD cards is not approved.

9. If the card was inserted with the label facing to the right, do not attempt to 

remove. Return the unit to Garmin for repair.

Uncontrolled if Printed

Содержание Cessna Caravan G1000

































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды