manualshive.com logo in svg

Garmin Cessna Caravan G1000, Руководство по линейному обслуживанию

Поделиться
Скачать
Garmin Cessna Caravan G1000 Скачать руководство пользователя страница 45

______________________________________________________________________________

____________________________________________________________________________

LMM for the Kodiak 100

Page 2-29

190-02102-00 Rev.4

2.4   CONFIGURATION MODE NAVIGATION

The user can navigate through different pages and page groups in Configuration Mode 
using the FMS knob

2.5   SOFTWARE FILES

Software files are defined by part number and version number in SN21-01 Kodiak 100 
G1000 Software Configurations and Updates. Each system LRU reports the software 
version it currently contains to the user in two places.

•  Normal System Mode: The Aux - System Status page lists each LRU and the 

reported software version.

•  Configuration Mode: The System Status page (System page group) reports more 

detailed LRU information, including software version, part number, and LRU status.

•  Software files are loaded to LRUs from the PFD System Upload page in 

configuration mode.

Table 2-6.  Data Transmission Indicators

The LRU is online and reports the item located next to the indicator 
box is communicating.

The LRU is online, and reports the item located next to the indicator 
box is not communicating.

The LRU is not reporting a status for the item located next to the 
indicator box. This may be because the data is not available, not 
applicable, or not expected.
The LRU is not reporting status for the item located next to the 
indicator box. This may be because the data is not available or is 
not expected.

 ‘True’ condition; i.e., necessary conditions have been met in order 
to activate the item.

‘False’ condition; i.e., necessary conditions have not been met in 
order to activate the item.

‘High’ condition; i.e., the system expects a high voltage or a high 
resistance input to trigger the item (fan operation, etc.).

‘Low’ condition; i.e., the system expects a low voltage or a low 
resistance input to trigger the item (fan operation, etc.).

Uncontrolled if Printed

Содержание Cessna Caravan G1000

































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды