Garmin Cessna Caravan G1000 Скачать руководство пользователя | Manualshive

Страница: 211 / 288

background image

______________________________________________________________________________

____________________________________________________________________________

LMM for the Kodiak 100

Page 5-13

190-02102-00 Rev.4

5.2.13 GWX 70R/75 Weather Radar

Unit Part Number: 011-03997-00 or 011-01768-20

Garmin Installation Manual: 190-02009-00

NOTE

Take care to avoid any contact between tools that can become magnetized
and the magnetron. Even momentary contact of a potentially magnetic
object with the magnetron case will cause serious weakening of the mag-
netic field. Use of non-magnetic tools (typically beryllium copper or tita-
nium) is recommended when installing or servicing the GWX 70R/75.

1. To Remove:

a) Remove the radome to get access to the weather radar by unscrewing the

screws from the dome; break the sealant with a flat, sharp-edged tool before
removing screws. Keep the screws to reinstall the radome.

CAUTION

Carefully hold the weather radar while loosening attachment nuts. Be sure
to support the radar unit as the fasteners are removed.

b) Remove the weather radar from the bulkhead assembly by removing the

socket head cap screws.

c) Remove the connector from the unit by pushing on the slide lock tab on the

side of the connector which releases it and pull the connector away from the
unit.

2. To Reinstall:

a) Put the weather radar in position on the bulkhead assembly.

b) Attach the connector to the unit by first pressing the slide lock tab on the side

of the connector, then align and mate the unit and wire harness connectors
together, and then release the slide lock tab. The locking tabs must be
engaged on both ends of the connector.

c) Install the socket head cap screws that hold the weather radar on the bulk-

head assembly. Ensure the connector wire is secure and not chafing. Add
strain relief or wire ties if necessary.

d) Make sure the wiring harness has been routed and secured in such a way it

cannot be struck by or interfere with unit movement throughout the full range
of sweep and tilt.

e) Install the radome according to Kodiak 100 AMM instructions.

Uncontrolled if Printed

«
...
209
210
211
212
213
...
»

Содержание Cessna Caravan G1000

































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cessna Caravan G1000

Бренд: Garmin Страницы: 104

Бренд: Bartscher Страницы: 91

Hot display unit 8x1/6GN-R

Бренд: Bartscher Страницы: 17

$Poly-Tex PX7030 Assembly Instructions Manual preview$

Бренд: Poly-Tex Страницы: 11

DynaVibe Classic

Бренд: RPX Technologies Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды