manualshive.com logo in svg

Garmin Cessna Caravan G1000, Руководство по линейному обслуживанию

Поделиться
Скачать
Garmin Cessna Caravan G1000 Скачать руководство пользователя страница 50

______________________________________________________________________________

____________________________________________________________________________

Page 2-34

LMM for the Kodiak 100

190-02102-00 Rev.4

2.8.2   Spare Supplemental Data Cards

To ensure availability of data cards that are both compatible and authorized, Garmin 
offers blank replacement cards. These blank cards do not contain any preloaded aviation 
databases and are intended for operators who have already purchased databases from 
the flyGarmin website. Databases for Garmin avionics can be purchased directly from 
www.flyGarmin.com. Blank replacement cards are available through authorized Garmin 
Aviation Dealers and Service Centers. Refer to Garmin Service Advisory 1506 for 
detailed information.

Uncontrolled if Printed

Содержание Cessna Caravan G1000

































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды